Rebar Reference

Steel Bar Weight Chart — kg per Metre, Every Size

Unit weight for 6mm to 40mm reinforcement bars in kg/m, kg/ft and per 12-metre bar, with the sutar equivalents used in Pakistan and the formula behind every figure.

12mm rebar = 0.888 kg per metre

10.65 kg per 12 m bar · about 94 bars to the tonne · the same whether it is Grade 40 or Grade 60

Pick a Diameter

Unit weight · per bar · bars per tonne

0.888
kg/m
Per Metre
0.271
kg/ft
Per Foot
10.65
kg
Per 12 m Bar
94
bars
Per Tonne

The Formula — d² ÷ 162

W = d² ÷ 162
W in kg per metre · d in millimetres

For a 12mm bar: 12 × 12 = 144, and 144 ÷ 162 = 0.889 kg/m. Multiply by the bar length for the weight of one bar, and by the number of bars for the total.

Published charts, including the one below, show 0.888 rather than 0.889. Both are right. The 162 shortcut is a rounding of the real calculation — area × density = (π/4 × d²/1,000,000) × 7,850 kg/m³ — which divides by 162.2 and gives 0.888. The gap is 0.1%, far inside rolling tolerance, so use whichever you can remember. The figures on this page use the exact calculation.

Working in feet

Divide the kg/m figure by 3.2808 to get kg per foot, or use W = d² ÷ 533 directly. A 12mm bar is 0.271 kg/ft, so a 40 ft bar weighs 10.82 kg.

Unit Weight Chart — 6mm to 40mm

Diameterkg per Metrekg per Foot12 m BarBars per TonneTypical Use
6 mm0.2220.0682.66 kg375Stirrups, ties, light mesh
8 mm0.3950.1204.74 kg211Stirrups, slab distribution
10 mm0.6170.1887.40 kg135Slab bars, footing ties
12 mm0.8880.27110.65 kg94Slab main bars, light beams
16 mm1.5780.48118.94 kg53Beams, column verticals
20 mm2.4660.75229.59 kg34Columns, heavy beams
25 mm3.8531.17546.24 kg22Large columns, rafts
32 mm6.3131.92475.76 kg13Heavy foundations, bridges
40 mm9.8653.007118.38 kg8Bridge piers, heavy civil

PK Sutar Sizes — What the Market Calls Them

Steel is still ordered by sutar in much of Pakistan. One sutar is one eighth of an inch, so the sutar number is the bar diameter in eighths.

SutarInchesNearest Metric Barkg per Metre
2 sutar2/8 = 0.250 in6 mm0.222
3 sutar3/8 = 0.375 in10 mm0.617
4 sutar4/8 = 0.500 in12 mm0.888
5 sutar5/8 = 0.625 in16 mm1.578
6 sutar6/8 = 0.750 in20 mm2.466
8 sutar8/8 = 1.000 in25 mm3.853
Sutar sizes are nominal, not exact. 4 sutar is 12.7mm but is supplied and billed as 12mm rebar. Order and check by the metric diameter, since that is what the weight is based on.

Grade Does Not Change the Weight

This is the single most common misunderstanding when buying steel, and it costs people money at the weighbridge.

Grade 40 and Grade 60 bars of the same diameter weigh exactly the same. Grade describes yield strength — 40,000 psi (Fe415) against 60,000 psi (Fe500) — not density. Both are steel at 7,850 kg/m³, so a 12mm bar is 0.888 kg/m either way.

What grade changes is how much steel the design needs. A higher grade carries more load per bar, so the engineer may specify fewer or smaller bars — but each individual bar still weighs what the chart above says.

If a supplier tells you Grade 40 is lighter and therefore cheaper per bar, check the weighbridge. A short-weight bar is an under-rolled bar, which is a quality problem, not a grade difference.

Frequently Asked Questions

0.888 kg per metre. The d²/162 shortcut gives 144 ÷ 162 = 0.889; the exact calculation gives 0.888, which is what published charts quote. A standard 12 metre bar therefore weighs 10.65 kg, and a 40 ft bar weighs 10.82 kg.
No. Grade is yield strength, not density. A 12mm bar weighs 0.888 kg/m whether it is Grade 40 (Fe415) or Grade 60 (Fe500), because both are steel at 7,850 kg/m³. Grade affects how many bars the design needs, not what each one weighs.
One tonne is 1,000 kg and a 12 metre bar of 12mm steel weighs 10.65 kg, so 1,000 ÷ 10.65 ≈ 94 bars. When ordering, state the tonnage and the diameter — "one tonne of 12mm" — rather than a bar count, since bar lengths vary by supplier.
Sutar counts eighths of an inch, so 4 sutar is 4/8 inch = 0.5 inch = 12.7mm. It is supplied and billed as 12mm rebar at 0.888 kg/m. Likewise 3 sutar is 10mm, 5 sutar is 16mm and 6 sutar is 20mm.
The D simply stands for deformed — a ribbed bar rather than a plain round one — and the number is the nominal diameter in millimetres. D12 is a 12mm deformed bar at 0.888 kg/m and D16 is 16mm at 1.578 kg/m. Nearly all reinforcement sold today is deformed.
It falls out of the geometry. Weight per metre = cross-sectional area × density = (π/4 × d²/1,000,000) × 7,850, which reduces to d² ÷ 162.2. Rounding to 162 is accurate to about 0.1%, well inside rolling tolerance.

Subscribe to our newsletter

New calculators, engineering guides and Survey GeoLink updates in your inbox. Free, no spam — unsubscribe any time.

We never share your address. See our privacy policy.